The idea of coupling exercises to increase training intensity or efficiency is about as old as the barbell itself. Supersets (exercises done back to back with no rest) and alternating sets (do an exercise, rest, then do a different one) have been around since Pangaea broke apart.
There are two main types of supersets:
These are both fine training modalities, and the agonist versus antagonist method actually has some science behind it showing that it potentiates increases in strength performance.
But what if we throw a wrench into this method and smash a whole muscle group, train it from various angles, and save a bit of time while we're at it? It's a strategy called zig-zagging and it's a very efficient way to stimulate growth.
Bodybuilders have said for decades that to create complete development of a muscle, it needed to be trained at multiple angles. There was a time when science scoffed at this, and fell back on the size principle: since motor units were activated from smallest to largest, it was unnecessary to train multiple angles.
They argued there was no "upper chest" or "inner biceps" that could be targeted through exercise selection, and that a muscle was either being worked in its entirety or not at all. Since then, "science" has had to eat crow because research revealed that different parts of a muscle are indeed stressed more or less depending on the movement being performed. Bros for the win, yet again.
This doesn't mean you can isolate one area all together. It just means that tension distribution on a muscle is greater in some areas of the working muscle group than others. If you're striving for complete muscular development, you need more than the compound movements.
Bodybuilders don't end up with that 3D look just because of drugs. Their training modalities play a major factor in their appearance and development. And now that we've established the importance of using multiple movements to stress a muscle at different angles, let's talk about how zig-zagging sets for the same muscle group does that.
Zig-zagging is a principle that bodybuilding physiologist, Scott Stevenson, uses in his Fortitude training protocol. It's basically a type of superset where you rest between the exercises.
A typical zig-zag superset:
Here's where it starts to look different: Choose two exercises that stress the same muscle at different angles/lengths and avoid movement redundancy. For example, do a seated press for shoulders, rest, then do a set of lateral raises. But something like seated barbell presses then seated dumbbell presses would be redundant.
In the former, you'd use a multi-joint movement, where tension is distributed throughout a greater degree of musculature, and then you'd do a single-joint movement where tension is distributed into a more concentrated area, i.e. the lateral delts.
This type of workout is typical for most guys seeking hypertrophy, but it eliminates the "do a movement, rest, do another set of the same movement, rest" methodology that's so prevalent in bodybuilding plans.
Note: Triceps and biceps don't really need zig-zagging, though no one is stopping you from doing it. This method mainly just applies to larger body parts, so we're going to stick with smashing the delts, back, legs, and chest.
Pick three sets of compounds for thighs, chest, and shoulders, as well as three favorite back thickness (rowing and deadlifts) and back width (vertical pulling) movements. Here are some examples. (Not a workout, just examples!)
The compound exercise is the staple of the workout and you build around it. Because you incur fatigue (duh) in the working muscle group after the isolation exercise, expect to take a hit when going back to the compound movement. In other words, you may have to adjust the weights down a bit on the second zig-zag if you have a specific target rep range in mind.
So if you hit 245 x 8 on bench press, then did flat flyes with the 40's for 10, don't expect to come back and hit 245 x 8 or more on the second superset. You could stick with the 245 and bang out what you can, or you can drop the weight for the second superset and focus on a target rep range. There's no hard and fast rule with that.
We don't have a lot of love for that gym bro that's doing a form of alternating sets, occupying two pieces of equipment, and taking his sweet-ass time between sets. You know the one...
There's a way to not be that guy. Pair things like press and lateral raise by simply bringing the dumbbells to the rack. Smith machine squats and sissy squats also work well, as do rack deadlifts and chins, because most racks have a chin-up bar.
Commit to the compound exercise and choose isolation exercises on the fly. If someone takes your delt lateral machine when you're ready to zig-zag over to it, you can do a dumbbell lateral instead or some other similar movement. Don't sweat it – you might even accidentally come up with a better combo of exercises.
Pick 2-3 compound movements and 2-3 isolation movements you're going to build the program around. Now rotate through those for a few months.
For example, for chest/shoulders/triceps you'd have 2-3 workouts you're rotating through that focus on different compound and different isolation exercises. Examples:
This is an awesome way to really pulverize yourself into multi-angle training submission. Zig-zagging has a high degree of training economy combined with metabolic stress and a bit of progressive overload. That's quite the delicious recipe for muscle building. Get going.
Ask Me Anything I receive great questions in my T Nation Community Coaching Lab. If…
Ask Me Anything I get a lot of great questions in my T Nation Community…
An Exaggerated Warm-Up Isn't Helpful I don't know when the lengthy warm-up became a thing,…
Training and Your Metabolic State When I think "workout," I think of speeds. Your metabolic…